Introduction: Existing radiator circuits often need a higher flow temperature than a standard heat pump curve provides, so the leaving-water limit, ambient operating envelope and boiler interlock decide whether an old-building retrofit is practical.
Old radiator circuits usually need hotter water than a standard heat pump curve delivers, so the top leaving water temperature decides whether the retrofit works. A retrofit contractor walks into a building where the radiators were sized decades ago for 80°C flow, the boiler is at the end of its life, and nobody is going to lift floors to fit underfloor heating. The practical question is whether the unit can hold the water temperature the existing panels were designed around, keep running through the coldest weeks of the local climate, and share the load with the old boiler while the budget is staged. Those answers decide the selection, and they are the parameters a manufacturer needs before quoting.
A radiator gives off heat in proportion to the gap between its mean water temperature and room temperature, not in proportion to the nameplate output of whatever is heating it. A panel sized for 80/60 flow at the design outdoor temperature produces noticeably less heat at 55/45, and in a building with original cast iron or steel emitters that shortfall shows up as slow morning recovery and complaints during the first cold snap. Most standard heat pump curves are built around 55°C flow because that suits new underfloor heating, while an old radiator circuit was designed for something hotter. CIBSE Guide B1 sets out how flow temperature, emitter output and boiler control interact in this kind of design work. Two routes exist. Change the emitters so a lower flow temperature delivers the same room output, or specify a unit that can push water up to the temperature the existing circuit was designed for. On occupied buildings with a tight budget, the second route is usually the practical one, which is why a monobloc with up to 75°C leaving water matters: at a 75/65 radiator schedule the original panels stay in service and the retrofit stops turning into a construction project. Running hotter water does cost efficiency, because the compressor works against a larger lift. That trade-off should be priced at design stage, and it is where hybrid operation earns its place — the heat pump carries the bulk of the season and the existing boiler covers the coldest peaks. The number that settles each room is whether the existing emitter still meets the room heat loss at the flow temperature you plan to run, and that comes out of the project hydraulic and heat load calculation. Bring the radiator schedule to the manufacturer and selection becomes a numbers conversation rather than a brochure one.
Four technical figures tell you whether a unit fits an existing building: capacity across the range, top leaving water temperature, the ambient operating limit, and whether it can control the existing boiler. Heating capacity and COP are rated at standard test conditions under EN 14511-1, so check rated output at conditions close to your design point rather than comparing one nominal figure with another.
Taken together, these four points answer the compatibility question a retrofit contractor actually has to close out. Capacity matches the load, temperature matches the emitters, the ambient limit covers the climate, and the interlock keeps the old boiler useful for the handful of days each winter that decide whether the tenant is warm.
A monobloc keeps the whole refrigeration circuit inside the outdoor casing, so the indoor side is water pipework only. On a retrofit that changes the labour profile: no refrigerant piping through the building, no brazing inside occupied rooms, and less dependence on F-gas certified technicians. For a contractor running several old-building projects at once, that reduces site complexity and keeps pressure testing and commissioning in one place instead of spread across two trades. Component choice is part of the support. Green Power Heat Pump builds this unit around a GMCC inverter compressor, a Swep plate heat exchanger, a Wilo pump and Danfoss control components, with an A+++ energy rating and full DC inverter modulation so flow temperature tracks the load instead of cycling on and off. The controller adds a 5-inch color touchscreen with daily, monthly and annual energy data, Wi-Fi remote access, SG Ready contacts, and clip-type connections for service access. At handover, named components, clear ratings and controls the client can read make the specification easier to defend when a building owner asks what they paid for. The planning conversation goes faster when you bring project data rather than a product request. Send the design outdoor temperature and room-by-room heat loss, the radiator schedule with design flow and return temperatures, the make and model of the existing boiler and its control interface, the electrical supply available, and the space and pipe route at the outdoor position. From that, a manufacturer can confirm the kW variant, say whether the three-phase 16 kW is needed, explain how the interlock should be wired, and state what the unit requires at commissioning. A like-for-like quotation should use the same project data so equipment comparisons reflect the actual building, not a nominal catalogue figure. If you are pricing a radiator retrofit now, send those parameters with your enquiry and ask for the matching variant, the documentation pack for your market and the current delivery arrangement for your order size. Ask about a pilot unit for the first building as well; one installed property is a practical way to confirm the flow temperature schedule before a larger order.
Radiator retrofits succeed or fail on water temperature, climate envelope and control. A unit that reaches 75°C keeps existing cast iron and steel panels in service, a -25°C operating limit covers the climates many European old-building projects sit in, and boiler interlock lets the old appliance earn its keep during peak cold while the heat pump runs the rest of the season. Boiler replacement policy is moving toward lower-carbon heating, but the practical fit still depends on the building's hydraulic and load data. Bring the heat load, radiator schedule, boiler details and electrical supply to the manufacturer, and confirm the 75°C radiator fit with project hydraulic and load calculations. R290 system installation and commissioning also require qualified technicians.
A: Radiator heat output follows the mean water temperature above room temperature, so a 75°C flow on a 75/65 or 70/55 schedule keeps original cast iron and steel panels close to their design output, where a 55°C curve would leave rooms short on the coldest days. The exact flow temperature each zone needs is confirmed with the project heat loss and hydraulic calculation.
A: For this R290 monobloc, heating operation runs from -25°C to 45°C ambient with leaving water adjustable from 10°C to 75°C. Check the project design outdoor temperature against the -25°C limit, then plan what covers the heating load at that design point, since output at extreme ambient differs from output at standard rating conditions.
A: Interlock control lets the heat pump and an existing gas or oil boiler operate as one system with a defined changeover, so the heat pump carries base load through most of the season and the boiler picks up peak demand during the coldest spells. It also lets an owner stage the investment, replacing the boiler later rather than in the same week.
Guide B1: Heating 2016 - CIBSE
European, American and International Standards online - iTeh Standards EN 14511-1
Decarbonising home heating - NAO report
Green Power Heat Pump R290 Monobloc DC Inverter Heat Pump product details
